Widescreen Gaming Forum
http://www.wsgf.org/phpBB3/

rFactor - I lost my triplehead resolutions
http://www.wsgf.org/phpBB3/viewtopic.php?f=68&t=13419		 Page 2 of 3
Author:  JKeefe [ 05 Jul 2006, 23:40 ]
Post subject:  rFactor - I lost my triplehead resolutions
I do have the extra modes installed. However, when I use VideoMode=147, the config utility runs when I start rFactor; it doesn't like that number and wants me to input a resolution in the config app.


Are you also choosing 3072x768 16bit or 32bit ?
Neither, as 3072x768 is not available in the config app, hence this thread. :) If it were available I would be selecting 32 bit, of course. I'm not about to run a 7900GT in 16 bit mode...
Author:  JKeefe [ 06 Jul 2006, 00:01 ]
Post subject:  rFactor - I lost my triplehead resolutions
I just reinstalled the latest Matrox Triplehead2Go software and the problem persists; I am taken to the rFactor config automatically because it doesn't like my settings.

Incidentally, there are a whole lot of other resolutions missing from this list, including common ones such as 1280x960. All of these are available in Windows.
Author:  JKeefe [ 06 Jul 2006, 05:59 ]
Post subject:  rFactor - I lost my triplehead resolutions
Well, I reinstalled Windows tonight (not because of this) and, not surprisingly, everything works fine now. 3072x768 is availabe in the config app.

However, 2 things are weird:
1. 85 Hz is not availabe as a refresh rate, only 75 Hz.
2. Config.ini says VideoMode=140.
Author:  RichieG [ 06 Jul 2006, 16:19 ]
Post subject:  rFactor - I lost my triplehead resolutions
Hi Jkeefe,

Well I am glad that you were able to get everything working again just sprry that it required a reinstallation of Windows.

140 is the right number for that mode as it is what I am getting here. 75Hz is the proper refresh rate when using that mode.
Author:  JKeefe [ 06 Jul 2006, 17:03 ]
Post subject:  rFactor - I lost my triplehead resolutions
140 is the right number for that mode as it is what I am getting here.
Ok... then why did you suggest VideoMode=147 :?:

75Hz is the proper refresh rate when using that mode.
The TMET is supposed to give me an 85 Hz refresh rate at 3072x768 in addition to 75 Hz. I would expect to see this listed as an available refresh in the rFactor config app.

How can I get an 85 Hz refresh rate at 3072x768? I use CRTs.
Author:  JKeefe [ 14 Jul 2006, 20:17 ]
Post subject:  rFactor - I lost my triplehead resolutions
A related question: where can I find the table that lists all of the values for the VideoMode parameter?
Author:  RichieG [ 17 Jul 2006, 04:27 ]
Post subject:  rFactor - I lost my triplehead resolutions
Hi JKeefe,

There is no specific table. We found out the the game will enumerate a list based on the EDID of the monitor, so this list will change from system to system which is why 147 was right for me on my system.

We are looking for ways to maybe work around this in the SGU.
Author:  JKeefe [ 17 Jul 2006, 16:55 ]
Post subject:  rFactor - I lost my triplehead resolutions
So did you just try numbers starting from 1, until you found that 147 worked? OR can you read the EDID and compile a list from that?

I suppose it doesn't matter. If everyone's list is different it's not really useful information. I'm just being curious.
Author:  RichieG [ 19 Jul 2006, 16:04 ]
Post subject:  rFactor - I lost my triplehead resolutions
Hi JKeefe,

So did you just try numbers starting from 1, until you found that 147 worked?


No that would have taken forever :-) When we run the config for the game and choose the surround resolution, all I did after that was open the cfg file and see what number was listed.


From what I have seen the numbers in the SGU should remain idle but will change if you put the extra resolutions from our expander tool in (as you have seen)
Author:  glen73 [ 15 Oct 2006, 06:42 ]
Post subject:  rFactor - I lost my triplehead resolutions
ok, i just bought a 32" wide, i cant change the native values in the config file or the config program. the highest i can get is 1280x1024 which sucks.
all the option in the config program only list 800x600 to 1280x1024.
i change videomode but it keeps going back to 11 (1280x1024). how can i get the res to a decent wide screen!
Page 2 of 3 All times are UTC [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/