Widescreen Gaming Forum

[-noun] Web community dedicated to ensuring PC games run properly on your tablet, netbook, personal computer, HDTV and multi-monitor gaming rig.
It is currently 16 Dec 2024, 02:27

All times are UTC [ DST ]




Post new topic Reply to topic  [ 13 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Bezel Management
PostPosted: 04 Aug 2007, 20:13 
Offline

Joined: 16 Jun 2006, 11:08
Posts: 91
I bought a digital TH2G and am having problems with bezel management.
I can enable it(and hot key it on and off) on the desktop,but it doesn't activate during games.

anyone have this issue or a possible solution?


Top
 Profile  
 


 Post subject: Bezel Management
PostPosted: 09 Aug 2007, 04:22 
Offline

Joined: 16 Jun 2006, 11:08
Posts: 91
I got this fixed with new vid card drivers,and reinstalling the matrox software

I guess you can delete this post


Top
 Profile  
 
 Post subject: Bezel Management
PostPosted: 09 Aug 2007, 06:51 
Offline
Founder
Founder
User avatar

Joined: 13 Oct 2003, 05:00
Posts: 7358
We'll leave it, in case someone has a similar issue. This may point them in the right direction.


Top
 Profile  
 
 Post subject: Bezel Management
PostPosted: 09 Aug 2007, 16:34 
Offline

Joined: 21 Apr 2006, 17:17
Posts: 643
Hmm, I have the latest drivers (or at least I did two weeks ago when I installed the Digital TripleHead2Go) and I'm also having this problem. I initially had it mapped to SHIFT+q, but once I realized that the Matrox software trapped the key and I couldn't type a capital Q on the desktop, I switched it to ALT+b (for "bezel"). Neither key combo seems to work in-game.


Top
 Profile  
 
 Post subject: Bezel Management
PostPosted: 09 Aug 2007, 17:21 
Offline
Insiders
Insiders

Joined: 08 Sep 2005, 23:22
Posts: 223
I too have found the bezelmanagement hotkeys to work intermittenly.

I have yet to find a pattern.

It should also be noted that using bezel management will cause you to lose some pixels from the extreme left and extreme right of your monitor array causing black "bars" on the extreme left and right. Personally I find the trade-off worth it..... but I was suprised as I was not aware this would be an issue.

Also... does anyone know if it is possible to enter the physical width of your bezels to assist in rendering the image? Although the image is hidden by the bezels, it does not exactly correspond to the bezel size and thus things transfer from one screen to another a tad faster than it seems it should.

_________________
Gigabyte GTX 980 - SLI

i7-4770k @4ghz

16GB Ram

Planar SA2311W 3D Vision monitors (x3)

Windows 7 x64 Ultimate SP1


Top
 Profile  
 
 Post subject: Bezel Management
PostPosted: 09 Aug 2007, 18:42 
Offline

Joined: 09 Aug 2007, 04:50
Posts: 3
I too have found the bezelmanagement hotkeys to work intermittenly.

I have yet to find a pattern.

It should also be noted that using bezel management will cause you to lose some pixels from the extreme left and extreme right of your monitor array causing black "bars" on the extreme left and right. Personally I find the trade-off worth it..... but I was suprised as I was not aware this would be an issue.

Also... does anyone know if it is possible to enter the physical width of your bezels to assist in rendering the image? Although the image is hidden by the bezels, it does not exactly correspond to the bezel size and thus things transfer from one screen to another a tad faster than it seems it should.


how do you set your hotkeys? Because on my side I can apply an hotkey like Alt-A and get it to work on windows desktop and unreal tournament 2003 with no problem.

Remember that the hotkey will apply for all the triplehead resolution bezel adjust, but each resolution will retain his left and right value. Example: set 3840x1024 with hotkey alt-a with left: 15 pixel and right:0 pixel, it won't be the same value for 3072x768, but it will be the same hotkey for change bezel. Remember to enable the bezel management in each triplehead mode you use.

With which game you have this issue?


Top
 Profile  
 
 Post subject: Bezel Management
PostPosted: 09 Aug 2007, 19:52 
Offline

Joined: 21 Apr 2006, 17:17
Posts: 643
It should also be noted that using bezel management will cause you to lose some pixels from the extreme left and extreme right of your monitor array causing black "bars" on the extreme left and right. Personally I find the trade-off worth it..... but I was surprised as I was not aware this would be an issue.
Keeping in mind the TripleHead2Go is "only" a device that splits up your triplehead video image, this isn't really surprising to me. The image gets shifted, not redistributed after a side has been chopped off. Besides, if the image was shifted to fill the screen, it would be distorted. Noticing the distortion shift as a game objects crosses from the center monitor to a side monitor could be just as distracting as having object "jump" over your bezels.

Also... does anyone know if it is possible to enter the physical width of your bezels to assist in rendering the image? Although the image is hidden by the bezels, it does not exactly correspond to the bezel size and thus things transfer from one screen to another a tad faster than it seems it should.
Did you use Matrox's blue screen to assist in your alignment? They provide a series of long straight lines to match everything up, so If you don't like how it looks perhaps you should try setting the parameters again.


Top
 Profile  
 
 Post subject: Bezel Management
PostPosted: 09 Aug 2007, 21:34 
Offline

Joined: 07 Nov 2006, 18:04
Posts: 37
Bezel management:

Thought there was a calibration screen included here for setup to align the screens, by visually aligning the diagonal lines one wouyld essentially set the amount of shift. This I thought was well explained on matrox's website.

Although I dont yet have it, I accept the blanks at the ends as a consequence, much rather have that then jumping images on the bezel edges.

as to teh buggy natureof the hot key, I'm not suprised, we still deal with powerdesk on occasion not loading, though in the registry for all users run ...

so, Waz ... should I go get one? :)


Top
 Profile  
 
 Post subject: Bezel Management
PostPosted: 09 Aug 2007, 23:32 
Offline
Insiders
Insiders

Joined: 08 Sep 2005, 23:22
Posts: 223
Bezel management:

Thought there was a calibration screen included here for setup to align the screens, by visually aligning the diagonal lines one wouyld essentially set the amount of shift. This I thought was well explained on matrox's website.

Although I dont yet have it, I accept the blanks at the ends as a consequence, much rather have that then jumping images on the bezel edges.

as to teh buggy natureof the hot key, I'm not suprised, we still deal with powerdesk on occasion not loading, though in the registry for all users run ...

so, Waz ... should I go get one? :)


Yes. A good buy IMHO. I'm VERY happy with my choice of three HP LP2065 1600x1200 20.1" screens as non-gaming work looks fantastic! Also, as I believe JKeefe has mentioned before, Ultramon is a MUST for multi-screen computing. The Matrox Powerdesk software is a joke in comparison.... although you obviously still need it for setting up bezel management.

I do use the line-up software to get the bezel lines lined up.... and it does work quite well. I'll tweak a bit more to see if I can perfect the bezels hiding the image. The image *does* hide behind the bezels and it is MUCH better IMHO than when I have BM off.... but it just seems that the image should be hidden a *tad* longer than it is. Hard to explain.... but, for example, when running Armed Assault in demo mode, there is a scene where a soldier walks across the area between two of the monitors. The time it takes him to walk "behind" the bezels (which measures a total of 32mm on my screens) is quicker than when he walks 32mm of screen distance without moving behind a bezel. Does that make sense?

Overall, I am quite pleased with the product and am glad Matrox decided to go this route as it enables me to continue upgrading my graphics cards while maintaining triplehead.

_________________
Gigabyte GTX 980 - SLI

i7-4770k @4ghz

16GB Ram

Planar SA2311W 3D Vision monitors (x3)

Windows 7 x64 Ultimate SP1


Top
 Profile  
 
 Post subject: Bezel Management
PostPosted: 12 May 2008, 03:06 
Offline

Joined: 19 Aug 2006, 19:16
Posts: 17
has anyone had a problem when trying to setup bezel management? when i click on the check box to "Enable" it it takes about 3 minutes before it actually gets checked and when i finally get it back it takes the same amount of time to adjust it. every one click adjustment does this.

is this a GXM thing or do i possible have something going on elsewhere?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 13 posts ]  Go to page 1, 2  Next

All times are UTC [ DST ]


Who is online

Users browsing this forum: No registered users and 13 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  




Powered by phpBB® Forum Software © phpBB Group