Widescreen Gaming Forum

[-noun] Web community dedicated to ensuring PC games run properly on your tablet, netbook, personal computer, HDTV and multi-monitor gaming rig.
It is currently 18 Nov 2024, 04:40

View unanswered posts | View active topics


Board index » Multi-Monitor Gaming » Multi-Monitor Gaming

All times are UTC [ DST ]



Post new topic Reply to topic  Page 1 of 2
  [ 15 posts ]  Go to page 1, 2  Next
  Print view Previous topic | Next topic 
Author Message
segfault
PostPosted: 12 Apr 2011, 03:29 
Offline

Joined: 04 Apr 2011, 20:30
Posts: 13
so i received my u3011 today, hooked it up, went into nvidia control panel to enable surround only to see an error message telling me that the 3007 needs to be replaced with another display for surround. all three monitors have the same resolution and refresh rate, so i figured it had to be the sync polarity. sure enough, after looking at the detailed specs for all 3 monitors this is what i found for their sync polarities:

3007: -/+
3008: +/-
3011: +/-

what exactly is sync polarity and can i change it on my 3007 to be the same as the other two?
Top
 Profile  
 


suiken_2mieu
PostPosted: 12 Apr 2011, 06:25 
Offline
Insiders
Insiders
User avatar

Joined: 20 Aug 2009, 04:20
Posts: 2351
Location: Virginia
I'm not sure about changing it. That would require a firmware update. But i'm really not sure if that's something physical or not.

BTW, if you don't mind me asking, how do those panels match with each other (I have 3 3007wfp-hc's and am looking for 2 more)

_________________
System Core: | Intel Core i5-2500K + ASUS P8Z68-V + 16GB Corsair XMS3 DDR3 1333 MHz | Win7 x64 | MSI R7970 Lightning 3GB [1105/1400] |
Display: | 3 x Dell Ultrasharp 3007WFP-HC @ 7680x1600 | Dell u3011 |
Top
 Profile  
 
segfault
PostPosted: 12 Apr 2011, 18:11 
Offline

Joined: 04 Apr 2011, 20:30
Posts: 13
I'm not sure about changing it. That would require a firmware update. But i'm really not sure if that's something physical or not.

BTW, if you don't mind me asking, how do those panels match with each other (I have 3 3007wfp-hc's and am looking for 2 more)



the 3007 and 3011 go together fine as their bezel thickness is almost the same. the 3008 bezel however is noticeably thicker than the 3007/3011.
Top
 Profile  
 
VRman
PostPosted: 15 Apr 2011, 04:46 
Offline

Joined: 29 Sep 2009, 05:04
Posts: 30
FWIW, I'm using a 3007 HC with a 3008 on each side and have no problems with Eyefinity.

Another thing: After calibration the 3007 HC matches the 3008 reasonably well, maybe a bit warmer/yellowish (could be the ageing) and less sharp (could be the coating). I was thinking of upgrading the 3007 HC to a 3011 now that they have come down in price, do you see any difference between them?
Top
 Profile  
 
segfault
PostPosted: 15 Apr 2011, 06:22 
Offline

Joined: 04 Apr 2011, 20:30
Posts: 13
FWIW, I'm using a 3007 HC with a 3008 on each side and have no problems with Eyefinity.

Another thing: After calibration the 3007 HC matches the 3008 reasonably well, maybe a bit warmer/yellowish (could be the ageing) and less sharp (could be the coating). I was thinking of upgrading the 3007 HC to a 3011 now that they have come down in price, do you see any difference between them?


AFAIK, eyefinity doesn't require that all the monitors have the same sync polarity which is probably why you have no problems. as far as 3007 vs 3011 goes, it does seem like the colors are more vibrant on the 3011 but then maybe it's just because my 3007 is kind of old.
Top
 Profile  
 
Paradigm Shifter
PostPosted: 15 Apr 2011, 13:22 
Offline
Editors
Editors
User avatar

Joined: 14 Oct 2003, 13:52
Posts: 5706
EyeFinity has no issues with sync polarities, correct.

And there's no way of changing it. :(
Top
 Profile  
 
segfault
PostPosted: 01 May 2011, 07:20 
Offline

Joined: 04 Apr 2011, 20:30
Posts: 13
in case anyone else has this problem, i was able to get these working in surround. i created a custom inf based off one of the monitors and then used that for all three.
Top
 Profile  
 
Paradigm Shifter
PostPosted: 01 May 2011, 13:19 
Offline
Editors
Editors
User avatar

Joined: 14 Oct 2003, 13:52
Posts: 5706
Would you share the .inf?
Top
 Profile  
 
segfault
PostPosted: 01 May 2011, 18:38 
Offline

Joined: 04 Apr 2011, 20:30
Posts: 13
Would you share the .inf?


here it is. keep in mind, this is specific to these dell monitors only. basically what i did was open up phoenix then load up the dell 3008wfp EDID from registry. i then edited it and removed all the display modes except 2560x1600 keeping the sync polarity as is for that mode. saved the modified EDID as a .dat file which i opened in MonInfo and finally saved it as an inf. finally, i went into device manager, uninstalled all 3 monitors (checked the option to delete their drivers) and reinstalled all 3 monitors using the below inf. once i rebooted and went into nvidia control panel i was able to enable surround. i *think* this worked for me because the 3007 and 3011 were able to be run at the same sync polarity as the 3008 in 2560x1600, even though they don't normally use the same polarity at that mode.

Code:

   ; INF file generated by Monitor Asset Manager (2.59.0.934), 4/16/2011
   ; Copyright (c) EnTech Taiwan, 1995-2011.
   ; Internet: http://www.entechtaiwan.com
   
   [Version]
   Signature="$WINDOWS NT$"
   Class=Monitor
   ClassGUID={4d36e96e-e325-11ce-bfc1-08002be10318}
   Provider=%MFG%
   DriverVer=4/16/2011, 1.0.0.0
   ;CatalogFile=YourSignedCatalogFile.cat
   
   [DestinationDirs]
   DefaultDestDir=23
   
   [SourceDisksNames]
   1=%DISC%
   
   [SourceDisksFiles]
   ;YourColorProfileFile.icm
   
   [Manufacturer]
   %VENDOR%=EDID_OVERRIDE,NTx86,NTamd64
   
   [EDID_OVERRIDE.NTx86]
   %PRODUCTID%=OVERRIDDEN-EDID.Install, MONITORDEL4035
   
   [EDID_OVERRIDE.NTamd64]
   %PRODUCTID%=OVERRIDDEN-EDID.Install.NTamd64, MONITORDEL4035
   
   [OVERRIDDEN-EDID.Install.NTx86]
   DelReg=DEL_CURRENT_REG
   AddReg=OVERRIDDEN-EDID.AddReg, MODE1, DPMS
   CopyFiles=OVERRIDDEN-EDID.CopyFiles
   
   [OVERRIDDEN-EDID.Install.NTamd64]
   DelReg=DEL_CURRENT_REG
   AddReg=OVERRIDDEN-EDID.AddReg, MODE1, DPMS
   CopyFiles=OVERRIDDEN-EDID.CopyFiles
   
   [OVERRIDDEN-EDID.Install.NTx86.HW]
   AddReg=OVERRIDDEN-EDID_AddReg
   
   [OVERRIDDEN-EDID.Install.NTamd64.HW]
   AddReg=OVERRIDDEN-EDID_AddReg
   
   [OVERRIDDEN-EDID_AddReg]
   ;Base EDID
   HKR,EDID_OVERRIDE,"0",0x01,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x10,0xAC,0x35,0x40,0x4C,0x36,0x32,0x35,0x1C,0x13,0x01,0x03,0x80,0x41,0x29,0x78,0xEA,0x8F,0x95,0xAD,0x4F,0x32,0xB2,0x25,0x0F,0x50,0x54,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xB0,0x68,0x00,0xA0,0xA0,0x40,0x2E,0x60,0x30,0x20,0x36,0x00,0x81,0x90,0x21,0x00,0x00,0x1E,0x00,0x00,0x00,0x10,0x00,0x0A,0x0A,0x0A,0x0A,0x0A,0x0A,0x0A,0x0A,0x0A,0x0A,0x0A,0x0A,0x0A,0x00,0x00,0x00,0x10,0x00,0xB0,0x23,0x40,0x30,0x20,0x36,0x00,0x81,0x91,0x21,0x00,0x00,0x1C,0x00,0x00,0x00,0x10,0x00,0x31,0x56,0x1D,0x71,0x1C,0x00,0x0A,0x20,0x20,0x20,0x20,0x20,0x20,0x00,0xF0
   
   [DEL_CURRENT_REG]
   HKR,MODES
   HKR,EDID_OVERRIDE
   HKR,,MaxResolution
   HKR,,DPMS
   HKR,,ICMProfile
   
   [DPMS]
   HKR,,DPMS,,1
   
   [MODE1]
   HKR,,MaxResolution,,"2560,1600"
   
   [OVERRIDDEN-EDID.AddReg]
   HKR,"MODES2560,1600",Mode1,,""
   
   [OVERRIDDEN-EDID.CopyFiles]
   ;YourColorProfileFile.icm
   
   [Strings]
   MFG="EnTech Taiwan"
   DISC="Monitor EDID Override Installation Disk"
   PRODUCTID="Dell DEL4035 (DEL4035 EDID Override)"
   VENDOR="Dell"
   
Top
 Profile  
 
Paradigm Shifter
PostPosted: 01 May 2011, 20:38 
Offline
Editors
Editors
User avatar

Joined: 14 Oct 2003, 13:52
Posts: 5706
It's a ray of hope for non Sync-Polarity-Identical monitors in Surround, though, which is awesome. :D
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 15 posts ]  Go to page 1, 2  Next

Board index » Multi-Monitor Gaming » Multi-Monitor Gaming

All times are UTC [ DST ]

Who is online

Users browsing this forum: No registered users and 9 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron




Powered by phpBB® Forum Software © phpBB Group